A failing comfort and convenience display unit that is sending corrupted data frames.; Damaged or chafed wiring in the communication bus between the display and the module that set the code.; Corroded or loose electrical connectors at the display or at the receiving module.; Low battery voltage or a weak charging system causing the display to boot improperly and send invalid data.; A software glitch or outdated firmware in the display or the receiving module.; Water intrusion into the display or its connectors, leading to intermittent signal corruption.; A faulty ground connection for the display, causing voltage fluctuations that corrupt its data output.

DTC codes / U05xx · Network communication / U05B2

U05B2Invalid Data Received From Comfort and Convenience Display A

U05B2 is a generic communication fault indicating that a control module received invalid or corrupted data from the comfort and convenience display, which is the screen or interface that manages climate, audio, and other cabin settings. The computer detected a message from that display that failed its internal validity check, such as a missing checksum, out-of-range value, or malformed data packet, so it flagged the signal as untrustworthy.

SystemNetwork

Code typeGeneric (all makes)

SeverityLow

Fix difficultyIntermediate

AreaNetwork communication

Symptoms you may notice

The check engine light or a communication warning light is illuminated on the dashboard.
The comfort and convenience display may flicker, freeze, or show garbled information.
Some cabin features like climate control or audio settings may become unresponsive or default to a safe mode.
Intermittent operation of the display, especially in cold or hot weather, can occur.
Often no symptoms besides the warning light, with all systems appearing to work normally.
Other unrelated warning lights may appear if the display shares a communication bus with other modules.

Common causes, most likely first

A failing comfort and convenience display unit that is sending corrupted data frames.
Damaged or chafed wiring in the communication bus between the display and the module that set the code.
Corroded or loose electrical connectors at the display or at the receiving module.
Low battery voltage or a weak charging system causing the display to boot improperly and send invalid data.
A software glitch or outdated firmware in the display or the receiving module.
Water intrusion into the display or its connectors, leading to intermittent signal corruption.
A faulty ground connection for the display, causing voltage fluctuations that corrupt its data output.

How to diagnose and fix it

Use a scan tool to read all stored codes and confirm U05B2 is current, then record freeze-frame data to see the conditions when it set.
Inspect the battery voltage and charging system output, as low voltage is a common cause of invalid data from electronic displays.
Visually inspect the display unit and its connectors for corrosion, water damage, or loose pins, and clean or reseat as needed.
Check the communication bus wiring for continuity, shorts to ground, or shorts to voltage between the display and the module that set the code.
If wiring and power are good, perform a software update or reflash of the display module if the manufacturer offers one.
Substitute a known-good display unit or use a diagnostic tool to monitor live data from the display to see if invalid frames persist.
Clear the code and road-test the vehicle to verify the repair, repeating the diagnostic steps if the code returns.

What the code does not always mean

A U05B2 code often appears after a dead battery or jump-start, when the display boots with low voltage and sends a single invalid data frame that the receiving module stores permanently.
Many technicians replace the comfort and convenience display only to find the real fault is a corroded ground wire behind the dashboard, which corrupts the display's data output under load.
The code can be set by a completely healthy display if another module on the same communication bus is flooding the network with errors, so always check for other U-codes first.
In some vehicles, the comfort and convenience display shares a bus with the body control module, and a failing body control module can mimic a display fault by misinterpreting valid data.
After repairing the underlying issue, the code may remain stored until several clean drive cycles occur, so do not assume the repair failed if the light stays on briefly.

Can I keep driving with U05B2?

The vehicle remains safe to drive because the fault affects only comfort and convenience features, not steering, braking, or engine operation. Avoid relying on the display for critical settings, and address the issue soon to prevent battery drain or intermittent operation of cabin systems.

Tools that help

Tools we recommend are in the Auto Veteran shop on Amazon. As an Amazon Associate we earn from qualifying purchases.

Guidance is general and written for all OBD-II vehicles. Exact tests and values vary by model, so confirm the fault before replacing parts.