01 Don't Panic! Here's What to Do When the Skidding Warning Li… • 02 100 Hilarious Things Mechanics Actually Say (That’ll Make Y… • 03 Free VIN Check: Top 10 Free Sites to Get a Used Car's Histo… • 04 Experts Reveal The Real Reason Some Cars Burst Into Flames … • 05 These Warnings Can Prevent Breakdowns And Extend Your Vehic… • 06 Direct Injection's Dark Secret: How Modern Engines Destroy … • 07 Radiator Cap Warning Signs: Save Your Engine from Overheati… • 08 Turbocharger: Troubleshooting Common Problems Associated Wi… • 09 That Faint Vibration In The Seat Could Be The First Sign Of… • 10 Ford Dealerships: A Global Network Across Six Continents •

DTC codes / U05xx · Network communication / U0572

U0572Invalid Data Received From Vehicle Motion Control Module A

U0572 is a communication fault indicating that a control module received invalid or corrupted data from the Vehicle Motion Control Module A over the vehicle's network. The computer detected a message from that module that failed its internal checksum or contained out-of-range values, so it flagged the data as untrustworthy rather than a total loss of communication.

SystemNetwork
Code typeGeneric (all makes)
SeverityMedium
Fix difficultyProfessional
AreaNetwork communication

Symptoms you may notice

  • Illumination of the anti-lock brake system (ABS) or traction control warning light
  • Illumination of the check engine light or a general stability control fault message
  • Intermittent or permanent disabling of advanced driver assistance features such as adaptive cruise control or lane keeping
  • A noticeable reduction in power or activation of limp mode in some vehicles
  • Often no symptoms besides the warning light, with the vehicle driving normally
  • Occasional harsh or delayed shifting if the motion control data feeds the transmission controller

Common causes, most likely first

  1. Corroded, loose, or damaged electrical connector at the Vehicle Motion Control Module A
  2. Chafed or open wiring in the controller area network (CAN) bus or other data bus between modules
  3. Failing Vehicle Motion Control Module A itself, often due to internal circuit faults or water intrusion
  4. Low or unstable battery voltage causing the module to send corrupted data frames
  5. Software or calibration error in the motion control module requiring a reflash or update
  6. A faulty sensor feeding the motion control module, such as a wheel speed or yaw rate sensor, causing it to transmit invalid data
  7. Electromagnetic interference from aftermarket accessories or poor grounding points

How to diagnose and fix it

  1. Perform a full scan of all modules to record stored, pending, and history codes, then clear codes and test-drive to see if U0572 returns immediately.
  2. Inspect the battery state of charge and charging system output, as low voltage is a common cause of invalid data frames.
  3. Locate Vehicle Motion Control Module A and check its connectors for corrosion, loose pins, or water intrusion, cleaning and reseating as needed.
  4. Check the data bus wiring for continuity, shorts to ground or power, and proper termination resistance using a digital multimeter.
  5. If wiring and power are good, substitute a known-good module of the same part number to see if the fault follows the module.
  6. Verify that the motion control module has the latest software calibration and perform a reprogramming if a technical service bulletin applies.
  7. After repairs, clear codes and perform a road test with a scan tool monitoring live data to confirm no invalid data frames are logged.

What the code does not always mean

  • U0572 often appears after a low-voltage event such as a jump start or a weak battery, and the module may be perfectly fine once voltage is restored and codes are cleared.
  • A wheel speed sensor or steering angle sensor that is slightly out of range can cause the motion control module to broadcast invalid data, so technicians who replace the module without checking sensor inputs often see the code return.
  • The code can be set by a single corrupted message during a network glitch, so a history-only U0572 with no current symptoms may not warrant any repair beyond clearing and monitoring.
  • Aftermarket electronic accessories wired into the CAN bus or poor ground connections can introduce noise that corrupts data frames, mimicking a failing module.
  • Some vehicles require a relearn or calibration procedure after battery replacement or module service, and skipping it can leave U0572 stored even when all hardware is good.

Can I keep driving with U0572?

If the vehicle drives normally and only the warning light is on, you can drive cautiously to a repair shop, but avoid towing, heavy loads, or aggressive driving. If the ABS or stability control warning is active, remember that those safety systems may not intervene in an emergency, so reduce speed and increase following distance.

Tools that help

Tools we recommend are in the Auto Veteran shop on Amazon. As an Amazon Associate we earn from qualifying purchases.

Guidance is general and written for all OBD-II vehicles. Exact tests and values vary by model, so confirm the fault before replacing parts.

Running on fumes Free guides aren't free to make. Top up the tank. Any amount, one time. Fuel the Garage