01 This Is Why Your Car Is Louder Than It Used To Be • 02 Smooth Shifting: Navigating Common Transmission Problems an… • 03 Turbocharged Engine Maintenance: Dos and Don’ts • 04 This Secret Driving Habit Can Quietly Destroy Your Brake Pa… • 05 Ignoring These Fuel Usage Signs Can Lead to Expensive Engin… • 06 How EVs are Reshaping Auto Repairs and Opening Doors for Me… • 07 Toyota Noah vs Nissan Serena: A Comprehensive Comparison • 08 Engine Timing: A Comprehensive Guide for Successful Adjustm… • 09 Experts Warn Against Using Heated Seats For Too Long On Cer… • 10 This Is Why Your Car’s Door Locks Keep Flickering •

DTC codes / U05xx · Network communication / U0567

U0567Invalid Data Received From Image Processing Sensor B

This code means the module responsible for the image processing sensor, typically a camera or vision processor used for driver assistance features, has sent data that the receiving control module considers invalid or corrupted. The computer detected a message that failed its internal plausibility or checksum validation, so it flagged the sensor's data stream as unreliable.

SystemNetwork
Code typeGeneric (all makes)
SeverityMedium
Fix difficultyIntermediate
AreaNetwork communication

Symptoms you may notice

  • A warning light for a driver assistance system, such as lane keeping or forward collision alert, may illuminate.
  • The vehicle may disable or limit features that rely on camera input, including adaptive cruise control or automatic emergency braking.
  • A message on the dashboard may state that the camera or sensor is unavailable or blocked.
  • Often no symptoms besides the warning light, especially if the fault is intermittent.
  • In some cases, the infotainment screen may show a blank or frozen camera view.
  • The vehicle may store related codes in other modules that share the same communication bus.

Common causes, most likely first

  1. A faulty or dirty image processing sensor, such as a camera with a obstructed lens or internal failure.
  2. Damaged or corroded wiring in the sensor's harness, especially at connectors exposed to the elements.
  3. A software glitch or outdated calibration in the image processing module or the receiving module.
  4. Low voltage or a weak battery causing intermittent communication errors on the controller area network (CAN) bus.
  5. A failing control module that receives the sensor data and incorrectly flags it as invalid.
  6. Aftermarket accessories or improper repairs that disturb the sensor's mounting or wiring.

How to diagnose and fix it

  1. Inspect the image processing sensor for physical damage, dirt, or obstruction and clean the lens area if necessary.
  2. Check the sensor's wiring harness and connectors for corrosion, loose pins, or chafed wires, and repair as needed.
  3. Clear the code and test-drive the vehicle to see if the fault returns, noting any conditions that trigger it.
  4. Perform a battery and charging system test to rule out low voltage as a cause of communication errors.
  5. Check for technical service bulletins (TSBs) or software updates for the image processing module and apply them if available.
  6. If the code persists, use a scan tool to monitor live data from the sensor and compare it with expected values to confirm a faulty sensor.
  7. Replace the image processing sensor or the receiving module only after confirming a hardware failure with proper diagnostic procedures.

What Most Techs Miss on U0567

  • A dirty or fogged camera lens is a common cause that many drivers overlook, and a simple cleaning often resolves the code without any parts replacement.
  • The code can be set by a weak battery or poor ground connection that causes intermittent data corruption on the CAN bus, so always check voltage and grounds before condemning the sensor.
  • After a windshield replacement or body repair, the camera may be misaligned or uncalibrated, leading to invalid data that triggers this code even though the sensor itself is fine.
  • Some vehicles require a specific calibration procedure after any camera-related service, and skipping it can cause the code to return immediately.
  • This code does not always mean the sensor has failed; it can be a symptom of a communication issue elsewhere in the network, so a full system scan is essential.

Can I keep driving with U0567?

You can generally continue driving, but be aware that advanced driver assistance features may be disabled, so do not rely on them. Avoid long trips or harsh conditions until the fault is diagnosed, and have the system checked promptly to maintain safety features.

Tools that help

Tools we recommend are in the Auto Veteran shop on Amazon. As an Amazon Associate we earn from qualifying purchases.

Guidance is general and written for all OBD-II vehicles. Exact tests and values vary by model, so confirm the fault before replacing parts.

Running on fumes Free guides aren't free to make. Top up the tank. Any amount, one time. Fuel the Garage