01 Mastering Motorcycle Hand Signals for Effective Communicati… • 02 U0003, U0004, U0005, U0006, U0007, and U0008: High Speed CA… • 03 Car Sensors Explained: What They Are, How They Work, and Wh… • 04 How to Calculate Height Using Angle and Distance • 05 What is the Purpose of Hazard Lights and How to Use Them Pr… • 06 5 Reasons Why Your Car Wont Start When The Engine is Hot & … • 07 17 Reasons Your Car Won’t Start and How to Resolve Them • 08 How a Car Engine Actually Works From Start to Finish • 09 What to Do If Your Car Only Starts When You Hit the Starter • 10 The Real Reason SUVs Are Dominating the Market •

DTC codes / U05xx · Network communication / U0544

U0544Invalid Data Received From Parking Assist Control Module B

U0544 means the vehicle's main computers received invalid or missing data from Parking Assist Control Module B, which is one of the modules that runs the parking sensors and related driver aids. The computer detected a communication problem on the controller area network (CAN) bus, not necessarily a failed sensor, so the fault could be wiring, power, or the module itself.

SystemNetwork
Code typeGeneric (all makes)
SeverityMedium
Fix difficultyProfessional
AreaNetwork communication

Symptoms you may notice

  • Parking assist warning light or message on the dashboard
  • Parking sensors or automatic parking feature stop working
  • Chimes or beeps from the parking assist system become erratic or silent
  • Often no symptoms besides the warning light
  • Other driver assistance features may be disabled as a precaution
  • Intermittent warning that comes and goes with bumps or weather changes

Common causes, most likely first

  1. Loose, corroded, or damaged wiring at Parking Assist Control Module B connector
  2. Failed Parking Assist Control Module B
  3. Low or unstable battery voltage affecting module communication
  4. CAN bus wiring fault between the module and the rest of the network
  5. Water intrusion or corrosion in the module or connector
  6. Aftermarket accessories improperly tapped into the CAN bus
  7. Software or configuration mismatch after battery replacement or module swap

How to diagnose and fix it

  1. Scan all modules for related communication codes and record freeze-frame data
  2. Inspect the battery, charging system, and ground connections for stable voltage
  3. Locate Parking Assist Control Module B and check its connector for corrosion or loose pins
  4. Perform a wiggle test on the module harness while watching live data for dropouts
  5. Check CAN bus resistance and continuity according to the service information
  6. If wiring and power are good, substitute a known-good module or reprogram the existing one
  7. Clear codes and verify the repair with a road test and a full scan

What U0544 really tells you about the module

  • U0544 is a communication code, so the parking sensors themselves are often fine and the fault lies in the module's power, ground, or network connection.
  • A weak battery or poor ground can set this code without any module failure, especially after a jump start or long storage.
  • Water leaks into the rear quarter panel or bumper area commonly corrode Parking Assist Control Module B connectors on many vehicles.
  • Aftermarket dash cams or alarm systems tapped into the CAN bus can corrupt data and trigger U0544 along with other U-codes.
  • The code may reappear after clearing if the underlying network fault is intermittent, so a wiggle test and live data review are essential.

Can I keep driving with U0544?

You can usually drive the vehicle, but parking assist and related driver aids may be disabled, so rely on your own mirrors and judgment when parking. Avoid ignoring repeated warnings because an intermittent network fault can spread to other modules and affect safety systems.

Guidance is general and written for all OBD-II vehicles. Exact tests and values vary by model, so confirm the fault before replacing parts.

Running on fumes Free guides aren't free to make. Top up the tank. Any amount, one time. Fuel the Garage